EP brand replacement gearbox for woods rotary gearbox

EP brand name alternative gearbox for woods rotary gearbox

NEW 40 HP GEARBOX Sleek Enter one three/eight twelve spline output Interchangable with industry common size i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Several A lot more

Features
(one) manufacturer new forty five horse power shearpin gearbox. This gearbox suits a number of various can make of 4′,5′ and some 6′ rotary cutters. I market a lot of these packing containers every single year for several diverse purposes and have ALL Alternative Parts for this box, but hopefully you will not likely have to worry about that.
Right here are the specs on the box:
*45 horse electrical power gearbox
*Common 1-three/eight” clean input shaft(where the pto shaft hooks on). The pto shaft is held on by a 1/2 shearbolt.
*size of the input shaft out of the gearbox is 3″ extended
*bolt gap sample for mounting is on the corners, 4-3/four center of gap to center of gap. It takes a 5/eight” bolt.
*twelve splined output shaft(in which the blade carrier hooks up on the bottom)
*1-9/16 outside the house measurement in excess of the output shaft splines- from the foundation of the output cap to the stop of the splines is 2-three/4″ long- overall length of the output shaft is 4-1/two” lengthy.
*requires a 1″ threaded castle nut and a carter important on the bottom of the output shaft to secure blade pan(NUT is integrated – – BLADE PAN IS NOT!!)
*all round height of the box from the top of the mower deck to the prime of the box is nine-1/two”
This is a reasonably heavy product (47 lbs.) so freight is not low cost, but we do not make everything off of freight, what ever ups charges us we charge you.
40 HP
1:1:forty seven Ratio
1-three/eight” Clean Enter Shaft with Shear Pin Gap
1-one/two” twelve-Spline Ouput Shaft
Bolt Pattern: six-one/two” (4) five/eight” Holes, five” Heart Hole Required for Shaft Assembly
The Input and Output Shafts Can’t be Obtained Serparately.
They are Sold as a kit.
The kit involves the following parts: input shaft, input gear, output shaft, output gear.
The Shaft Package Cannot Be Divided.

EP model substitute gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Manual
Is your mower leaking, creaking or in any other case carrying out incorrectly? You have occur to the correct spot.

Study below for the most frequent troubles with rotary cutter gearboxes and their remedies (from fast and dirty, to expert).

Leaking Bottom Seal:
If you’ve wrapped some baling or fencing wire all around your output shaft and blown the seal, the expert factor to do is to change the seal.
If your output seal is intact, and you are capable to get ID, OD and thickness measurements (in millimeters), most bearing properties can order you up a generic double-lip seal that will get you back again up-and-managing. If not, give us a phone and we can support you form out what you require.
A dental select is the easiest way to take away the aged seal prior to pressing in the new one particular.
If you might be fortunate ample to have a slow-leak, the quick and filthy approach is to operate automotive-variety grease in the gearbox until finally the new seal will come in. Be certain to verify and incorporate grease more often than you would with oil, as this is NOT a expert fix.

Damaged Output Shaft:
Uh oh. You strike one thing that didn’t transfer. The great information is that the output shaft on most gearboxes is relatively straightforward to replace. The negative information is… it truly is not often an isolated failure.
The very first issue to do is to consider apart your gearbox and evaluate the full extent of the harm. If it is actually just the output shaft, you should be ready to change it out, no difficulty. The output shafts start at about $70 and go up in value relying on the measurement of the gearbox.
However, in most circumstances, the bearings ($20/ea), seals ($ten/ea) and gear-set ($70) will also usually consider a beating. If you happen to be unfortunate, the output cap ($80) will also suffer some harm.
In this scenario, it is typically cheaper to replace the gearbox. Assess the price tag of components to the expense of an whole, new, warrantied gearbox. Often, even pros have to know when to phone it a working day.

I Want to Adjust my Enter Shaft:
If you are fatigued of shifting shear pins or looking again and observing that your mower hasn’t been chopping, you may possibly want to put in a slip-clutch pto shaft (Yes, we market these as well).
This normally needs installing a 540-type, six-spline input shaft ($85) on your mower’s gearbox.
Blessed for you, we did a publish-up on our website. It really is called “How to alter the enter shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound type-of similar above-the-mobile phone. The best issue to do is to disassemble your gearbox and just take a search at the gears and bearings. The issue will usually current itself in the way of broken/missing gear tooth, toasted gears (like that image on our property web page), or blown bearings.
If every thing seems normal, try out adjusting the equipment-mesh. This is done with the mylar “gaskets” that sit in between the principal gearbox circumstance and the enter/output caps. Try adding or removing some of these spacers until your gears have roughly one/eight”-one/four” of free engage in. Professionals can order replacements ($1-2) in various thicknesses, but we recommend the rapid and soiled technique of cutting your personal out of a sheet of mylar.
Don’t forget to re-seal the gearbox with RTV following you have found the correct mix. Even even though they’re referred to as “gaskets”, they is not going to seal your gearbox on their own.

After visiting our http://agricultural-gearbox.xyz/agricultural-gearbox/electric-film-reeler-roll-up-units-winch-for.html you would know the brief conversation about the Gearbox for Agricultural Machinery.