Worm get gearbox with motor
worm motor
A robust worm-drive gearbox powered by an MM28 motor. Ideal applications where an easy to fit, high torque outcome is required. Ideal for student based assignments which includes robots and buggies.
The unit has been designed so that the output shaft could be ‘clicked’ in and out for modification. E.g. cutting down to size. The engine is snap fitted into its cradle to engage the gear and worm.
Details
1 – 6V DC
0.1A to 1A based on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + engine: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the electric motor is not turning. The high equipment ratios of 216:1 or 336:1 make this gearbox appropriate for little walking robots, lifting mechanisms, and additional applications where high torque is desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draw up to some amps, making them perfect applicants for the DRV8833 motor driver carrier. Engine overheating can be due to excessive stalling, also at suprisingly low voltages. We advise that you use stall-detection sensors, or just check out your robot, to ensure that it doesn’t stall for lots of seconds at a time.
This gearbox has a 4 mm diameter, round output shaft, which works together with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal mounting hub also suits on small threaded end of the shaft, although it is not especially intended to work with this type of shaft (the hub’s set screw could damage the thread on the shaft).
Ever-Power gear motors will be economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical right angle worm geared motors arranged new criteria for reliability, efficiency and economy with unparalleled features which includes hollow shafts in the smallest sizes. An inverter friendly design provides for easy integration today and a truly future proof alternative. The Ever-Power gear electric motor offers total versatility in mounting options includes shaft, base, encounter, and flange solutions. The motor terminal box could be mounted in substitute positions rotated in 90º steps around the engine frame providing for unparalleled integration possibilities.
Ever-Power gear motors comply with UNITED STATES and International criteria, including NEMA, IEC, CSA, and CE, the Ever-Power series allows for worldwide acceptance, a genuine total solution for our global clients.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose evidence,and can be used outdoors or in wet and dusty environments without the use of additional enclosures. Complete rated output is available at the result shaft of the machine.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Totally enclosed, sealed against dust and water spray
Lubrication change first after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Regular), IP66 (Optional)
Additional features:
Connecting with Connect connectors.
With included inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to Sobre 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm gear motors are the alternative for applications requiring a part turn, optional dual result, or an inability for the engine to be back driven. The DC correct angle equipment motors are made for constant and intermittent duty procedure. Our right angle gear reducers are designed with a number of mounting plate options, making them perfect for a variety of DC engine based applications. You can expect 12 ratios which range from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ hours (varies by application)
EP Products Worm Equipment Motors are designed to generate high torque in a little package size. Worm Equipment Motors are excellent for applications that want a personal- locking or breaking characteristic since the result shaft can’t rotate when there’s no power applied. On top of that, Worm Gearheads can transfer movement in 90 degrees. With various decrease ratios, precision slice gears, voltages and sizes, EP Items has a DC Worm Gear Motor solution for the application.
Features and Benefits
Very High Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Capability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Protection Door Locks / Industrial Conveying Systems / Security Gates / Teeth Chair / Ambulance Cots & Stretchers Quite a few DC Motors could be complimented with among our Worm Gearheads. EP Products will continue to work with you to design and manufacture a Worm Gear Motor that may optimize the efficiency of your unique application.
Built to your specific requirements
Motor Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Lower / Round / Splined / Other)
General Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm motor uses a metal gear box for strength and a high torque output. Because of the special mechanical structure of the worm drive the electric motor output shaft is self locking and can not be rotated.
This part runs on the two wire connection and supports direction control as well as PWM speed control. Ranked voltage is 12v and can obtain 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Rated Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear products from EP DRIVESYSTEMS especially display their power in applications where high gear ratios are necessary. Our worm geared motors happen to be consequently optimally suited for make use of in intralogistics, packaging technology and the meals & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a higher overload capacity
Maintenance Friendly
Washdown versions allow simple and efficient cleaning of the get system.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users optimum freedom.
The modular system for maximum flexibility: Our EP worm gear units
There are many applications that want drive systems, and each of these has its unique requirements. The EP series worm equipment motors can be quickly and effectively adapted to meet your needs.
Worm gear products impress with their superior power density and compact style. If required, we can also source them with the highly effective nsd tupH surface treatment.
As well as the basic EP housing, you can expect an extensive line of bolt-on components to customize the merchandise including torque arms, shaft addresses and output flanges. These can be easily field set up, but we will also be pleased to assemble the average person components for you.
Discover more about our modular SI worm geared motors!
Find out more
Smooth and Clean: The EP worm gear unit SMI
SMI worm gear devices feature a soft, corrosion-resistant alluminum alloy casing. Optional nsd tupH surface area conversion makes this product ideally suited for harsh and demanding industries like food processing and pharmaceuticals.
Adaptable input designs such as for example NEMA, IEC or direct motor mounts in extra foot or flange mounted casing designs.
Worm geared motors
Worm geared motors for little power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared motor program. The units have on all sides distinct fixing possibilities and enable a simple assembling for the client.
Various other drive configurationscan be created by use of built-on accessories (e.g. torque arm and result flanges). The housings are made in light weight construction out of aluminium die cast. Engine attachment is realised in general by means of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, result shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/installation:uniblock, flange, torque arm
Buy Worm Travel Gearbox with Engine – incorporating the next features: 1 to 6V voltage rating, 17100 rpm simply no load rate, 220g-cm stall torque, 3mm shaft size, 60mm long, 35mm wide, 40mm high, a good robust worm drive gearbox powered by an MM28 engine (included), most suitable for applications where a simple to fit, high torque outcome is required, nylon housing and equipment, requires light oil or perhaps silicon grease lubrication, perfect for student based tasks including robots and buggies.
Most suitable for applications where an easy to match, high torque outcome is required
Perfect for student based projects including robots and buggies
Reversible Large torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Reversible Great torque Turbo Worm Gear Engine JGY370 DC 12V 40RPM
Features:
The engine is Gear DC electric motor with micro-turbine worm, you can change the wiring-connection to improve motor rotation.
Turbo worm geared engine with self-lock, that is, in the case of motor without electric, the end result axis is fixed, self-lock.
The reducer output shaft arranged vertically with the motor shaft, whole engine output shaft relatively-short than general gear electric motor, widely used to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Output torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windowpane, door, Mini winch. Ect.
In sumo robot or combat robot competition where substantial holding torque’s engine is essential to avoid your robot being pushed by your opponent robot. The worm equipment is definitely a better option when compared to spur gear motor. How come worm gear so unique? Check this wiki out: Worm Get.
“Unlike with ordinary gear trains, the direction of transmission (insight shaft vs result shaft) is not reversible when using large reduction ratios, due to the greater friction involved between your worm and worm-wheel, when usually an individual start (one spiral) worm can be used. This is often a advantage when it’s desired to eliminate any probability of the result driving the input.”
In other terms, it is hard to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking because of the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g